Przejdź do treści

Informacja o tym pliku do pobrania

About this upgrade (29/07/2011)

This file updates your Hard Disk Recorder firmware to version 4.21.r8585, and provides the following benefits:

Improvements in this version:

  • Solves the issue of the Recorder’s continued rebooting caused by OAD signals for other devices.
  • Addition of Video data file playback feature. (For details about the "Playable types of files" please refer to the page 43 of the Operating Instructions).
  • Multi channel audio is output via HDMI (as a result, sound will also be output in the following trick play modes: fast forward X2 and X4, and in slow forward).
  • Software stability improvement.

If you experience any issue with this update, please contact Sony.

Applicable models

  • SVR-HDT500
  • SVR-HDT1000

Please confirm your recorder’s model name on the front panel.

Please follow the update instructions carefully. Failure to follow the instructions may interrupt the update process and may cause the Recorder to be unresponsive or to require repair.

Do not power off the Recorder or disconnect it from the AC power outlet. Loss of power during the installation of the firmware update may cause the Recorder to be unresponsive or to require repair.

Instalacja

Before you start:

  • Please use a quality branded USB memory stick to perform the firmware update.*
    * Some USB memory sticks may not be recognized.

  • You need a computer with a USB memory slot to copy the software.

Check the HDD Recorder firmware version:

  1. Power on the television and make sure it is tuned to the inputs to which the HDD Recorder is connected.

  2. Power on the HDD Recorder.

  3. On the remote control press the “SYSTEM MENU” button.

  4. Select “Others” then press the “ENTER” button.

  5. Select “Diagnostics” then press the “ENTER” button.

  6. Select “System Information” then press the “ENTER” button.

    The firmware version currently installed on the HDD Recorder will be listed on the television screen as “SW version:”.

    If the version number is 8585 or higher, your HDD Recorder does not need to be updated.

  7. To exit, press the “RETURN” button 3 times.

Download procedure:

Please read all the information carefully and thoroughly before downloading and installing any file.

You need to accept the disclaimer below before downloading the file.

After you have accepted the disclaimer, save the file to your computer Desktop. When the update is complete, check that the file is 28,570,377 bytes.

To do so, right click the file, select “properties” and check that the “General” tab displays the following size information:



If the size information displayed on your computer is different, delete the downloaded file, clear your internet browser's cache and download it again.

Unzip the download zip file and copy to a root folder of USB memory.

Important note: Make sure the copy was correctly done without any error. In case of doubt, copy it again.

Firmware update procedure:

  • Do not turn off the HDD recorder or disconnect the HDD recorder from the power supply during the update process.Doing so may damage your Recorder and make it unusable, and would require a repair of the HDD recorder.
  • Do not press any button, except as instructed, until the update is complete.Doing so may damage your Recorder and make it unusable, and would require a repair of the HDD recorder.

The firmware update process may take up to 5 minutes.First read the whole procedure before starting to update the firmware of your HDD recorder.

  1. Power on your HDD recorder by pressing "POWER" button.

  2. Insert the USB memory stored update software to front panel USB jack.

  3. Press the “SYSTEM MENU” button on the remote control.

  4. Select “Others” then press the “ENTER” button.

  5. Select “Maintenance” then press the “ENTER” button.

  6. Select “Software Update” then press the “ENTER” button.

  7. Enter your password. (Default password is “0000”)

  8. Select “USB” then press the “ENTER” button. The update starts automatically.

  9. Do not perform any operations until the update completes.
    When update starts, a TV’s screen will appear a updating message.

  10. The recorder will reboot automatically.

  11. Press the “TITLE LIST” button on the remote control.

  12. Press the “OPTIONS” button.

  13. Select “Remove USB” then press the “ENTER” button.

  14. Remove the USB after the message “USB is disconnected” appears.

  15. Press “Power” button to power off the set.

  16. The Update is complete now.

If an error message appears, power off your HDD Recorder and repeat the update procedure from the beginning.

Check the HDD Recorder firmware version:

  1. Power on the television and make sure it is tuned to the inputs to which the HDD Recorder is connected.

  2. Power on the HDD Recorder.

  3. On the remote control press the “SYSTEM MENU” button.

  4. Select “Others” then press the “ENTER” button.

  5. Select “Diagnostics” then press the “ENTER” button.

  6. Select “System Information” then press the “ENTER” button.

    The firmware version currently installed on the HDD Recorder will be listed on the television screen as “SW version:”.

    If the version number is not 4.21.r8585, repeat the update procedure from the beginning.

  7. To exit, press the “RETURN” button 3 times.

Informacja o pliku

Nazwa pliku

  • 4.21.r8585.zip

Rozmiar pliku

  • -